High performance oscillator with 2-mW output power at 300 GHz

Material structures and device structures of a 100-GHz InP based transferred-electron device are designed in this paper. In order to successfully fabricate the Gunn devices operating at 100 GHz, the InP substrate was entirely removed by mechanical thinning and wet etching. The Gunn device was connected to a tripler link and a high RF(radio frequency)output with power of 2 mW working at 300 GHz was obtained, which is high enough for applications in current military electronic systems.     

Tuneable Sagnac comb filter including two wave retarders

In this paper we study theoretically and experimentally a wavelength-tuneable Sagnac birefringence filter. The device is a Sagnac interferometer including a symmetric fibre coupler and a length of high-birefringence fibre in the loop. A wave retarder is inserted at each end of the birefringent fibre for absolute wavelength tuning. We show theoretically that wavelength tuning through wave plate orientation ensuring constant amplitude of the filtering function is possible only if a minimum of two wave retarders are included in the setup. The position of the transmission peaks then varies linearly with the angle of one of the retarders and can be adjusted over one entire channel spacing. This happens only when a quarter-wave retarder and a half-wave retarder are used, if the former is oriented at 45° with respect to the fibre birefringence axes, while the orientation of the latter serves as the adjustment parameter. The theoretical predictions are confirmed by the experimental results.     

Operation principle of self-phase compensated optical waveguide isolator

A theory is developed for the self-phase compensated optical waveguide isolator recently reported in the literature. The operation principle of such device is explained in terms of synchronization of phase and power conversion. The effect of balancing phase mismatches of the two convertors on achieving a proper percentage of mode conversion is revealed. The way to make use of the phase mismatches of different sections to accommodate the different requirements in phase relationship for the reciprocal and nonreciprocal mode convertors is discussed. The theory is extended to the case where phase compensator is used. It is demonstrated that the introduction of phase compensator separates the adjustment of phase from the adjustment of power for the mode convertors so that relaxes fabrication tolerances of such devices. An isolator consists of three phase mismatched waveguide sections is designed and simulated. The simulation results confirm the self-phase compensation theory.     

Optically Triggered Control of the Charge Carrier Density in Chemically Functionalized Graphene Field Effect Transistors

Field effect transistors (FETs) based on 2D materials are of great interest for applications in ultrathin electronic and sensing devices. Here we demonstrate the possibility to add optical switchability to graphene FETs (GFET) by functionalizing the graphene channel with optically switchable azobenzene molecules. The azobenzene molecules were incorporated to the GFET channel by building a van der Waals heterostructure with a carbon nanomembrane (CNM), which is used as a molecular interposer to attach the azobenzene molecules. Under exposure with 365 nm and 455 nm light, azobenzene molecules transition between cis and trans molecular conformations, respectively, resulting in a switching of the molecular dipole moment. Thus, the effective electric field acting on the GFET channel is tuned by optical stimulation and the carrier density is modulated.     

Single‐Molecule Sensing of Environmental pH—an STM Break Junction and NEGF‐DFT Approach

Sensors play a significant role in the detection of toxic species and explosives, and in the remote control of chemical processes. In this work, we report a single‐molecule‐based pH switch/sensor that exploits the sensitivity of dye molecules to environmental pH to build metal–molecule–metal (m‐M‐m) devices using the scanning tunneling microscopy (STM) break junction technique. Dyes undergo pH‐induced electronic modulation due to reversible structural transformation between a conjugated and a nonconjugated form, resulting in a change in the HOMO–LUMO gap. The dye‐mediated m‐M‐m devices react to environmental pH with a high on/off ratio (≈100:1) of device conductivity. Density functional theory (DFT) calculations, carried out under the non‐equilibrium Green’s function (NEGF) framework, model charge transport through these molecules in the two possible forms and confirm that the HOMO–LUMO gap of dyes is nearly twice as large in the nonconjugated form as in the conjugated form.     

Miniaturized molecularly imprinted polymer extraction method for the gas chromatographic analysis of flavonoids

In this study, the use of monolithic molecularly imprinted polymers in a micropipette tip format allowing the simple and fast extraction of flavonoids from standard solutions and a black tea sample is demonstrated. The imprinted polymer employed quercetin, methacrylic acid or 4‐vinylpyridine, and ethylene glycol dimethacrylate as template, functional monomer, and cross‐linker, respectively. Surface morphologies of the quercetin‐imprinted polymers and the corresponding nonimprinted polymers were characterized by SEM. Extraction of flavonoid standards was performed to evaluate the selectivity and recovery with these imprinted and nonimprinted polymers. Flavonoid compositions in aliquots eluted from the tips were identified using fast GC with flame ionization detection. Maximum specific capacities of 0.2, 5.7, and 16.0 mg/g for catechin, morin, and quercetin, respectively, were obtained with the imprinted polymer prepared with methacrylic acid, with the corresponding recoveries of 99.8, 98.8, and 95.4%, respectively. Efficient extraction by the quercetin‐imprinted polymer of epicatechin, catechin, and quercetin from an apple‐flavored black tea sample was achieved, with GC–MS employed for compound identification for both the tea and extracted samples.     

Construction of a portable sample preparation device with a magnetic poly(methacrylic acid‐co‐ethylene dimethacrylate) monolith as the extraction medium and its application in the enrichment of UV filters in water samples

A portable sample preparation device with a magnetic polymer monolith as the extraction medium was constructed. The monolith was synthesized by polymerizing methacrylic acid and ethylene dimethacrylate around a cylindrical magnet. In this way, the monolith with a magnetic core could be readily attached to the extraction device by magnetism. The constructed device was evaluated for the enrichment of UV filters in water samples, followed by high‐performance liquid chromatographic analysis. The extraction efficiency for the targets was satisfactory with no matrix interference. Good linearities were obtained for the UV filters with the correlation coefficients >0.9986. The limits of detection and quantification for the UV filters were 0.3–0.8 and 1.0–2.4 ng/mL, respectively. The recoveries of the UV filters from the spiked water samples at the concentration of 100 ng/mL were 95.3–101.7%, with relative standard deviations <10%. Accordingly, the proposed portable device was demonstrated to be suitable for on‐site simultaneous sampling, purification, and preconcentration within a single step.     

大视场光学遥感器焦平面板的研制

焦平面板作为承载TDICCD器件的部件,其强度、动静态刚度、热稳定性直接影响到遥感器的成像质量.针对目前光学遥感器大视场、宽覆盖的发展趋势,设计了一种新型的焦平面板.选用性能指标优良的高体份SiC/Al复合材料,既满足了结构设计指标的要求,同时又大大降低了产品重量.通过有限元模拟仿真分析和相关试验,验证了设计方案的可行...     

Intersubband transitions in Al0.82In0.18N/GaN single quantum well

The influence of the width of a lattice-matched Al_0.82In_0.18N/GaN single quantum well (SQW) on the absorption coefficients and wavelength of the intersubband transition (ISBT) has been investigated by solving the Schrödinger and Poisson equations self-consistently. The wavelength of 1—2 ISBT increases with L, the thickness of the single quantum well, ranging from 2.88 μm to 3.59 μm. The absorption coefficients of 1—2 ISBT increase with L at first and then decrease with L, with a maximum when L is equal to 2.6 nm. The wavelength of 1—3 ISBT decreases with L at first and then increases with L, with a minimum when L is equal to 4 nm, ranging from approximately 2.03 μm to near 2.11 μm. The absorption coefficients of 1—3 ISBT decrease with L. The results indicate that mid-infrared can be realized by the Al_0.82In_0.18N/GaN SQW. In addition, the wavelength and absorption coefficients of ISBT can be adjusted by changing the width of the SQW.